China Suppliers Factory Integrated MIG 250A Gasless Welding Machine with Enhanced Control and Heating Efficiency
Detailed Information
IGBT Inverter Automatic MIG Welding Machine Installation & Environment Requirements:
- The installation area should be firm enough to support the welder.
- It is forbidden to install the welder in places where water splashes may be generated, such as water pipes.
- Welding operations must be performed in a relatively dry environment where the air humidity is normally not greater than 90%.
- The ambient temperature shall be between -10°C and +40°C.
- Do not perform welding in dusty or corrosive gas-containing areas.
- Do not place the welder on a tabletop with an inclination greater than 15°.
Protective Circuit System Notice:
The welder has been installed with overvoltage, overcurrent and overheating protective circuits. When the grid voltage, output current and internal temperature exceed the set standards, the welder will stop working automatically; but excessive use (such as excessive voltage) will still cause damage to the welder, so the following matters shall be noticed:
● Prohibit excessive voltage
In general, the automatic voltage compensation circuit inside the welder will ensure that the welding current is kept within the allowable range. If the supply voltage exceeds the allowable value, it will damage the welder.
● Prohibit overload
Operators shall use the welder according to its allowable load duration rate and maintain the welding current within the maximum allowable load current. Current overload will remarkably shorten the life of the welder or even burn it.
If the welder exceeds the standard load duration rate in working, it may suddenly enter the protection state and stop working. This indicates that once the standard load duration rate is overtaken, it will heat up to trigger the temperature control switch to stop the welder, and the yellow indicator light on the front panel is on at the same time. In this case, do not pull out the power plug. Let the fan cool down the welder. When the yellow indicator light is off and the temperature drops to the standard range, start welding.
Main Features
- All movements adopt the latest and mature IGBT full-bridge inverter technology.
- IGBT inverter technology, less welding spatter and beautiful welding seams.
- Complete undervoltage, overvoltage and current protection, safe and reliable.
- Accurate digital display of current and voltage preset, easy and intuitive operation.
- High pressure and slow wire feeding to start the arc, the arc will not burst the wire, and the arc will be closed to remove small balls.
- Constant voltage output characteristics, CO2 welding, one machine for multiple purposes.
- With self-locking/non-self-locking mode, greatly reducing operating intensity.
- Three-proof design for key parts, suitable for various harsh environments, with stable and reliable operation.
Working Connection Diagram
Product Parameters
| Model | NBC-315K | |
| Rated Input Voltage | 220V 50Hz/60Hz | 380V 50Hz/60Hz |
| Rated Input Power | 7.5Kva | 13Kva |
| No Load Voltage | 57V | 60V |
| Rated Output | 200A/24V | 315A/30V |
| Voltage Regulation | 14-32V | |
| Rated Duty Cycle | 60% | |
| Power Factor | 0.8 | |
| Insulation Class | F | |
| Shell Protection Grade | IP21S | |
| Suggested Welding Wire | 0.8-1.0mm | |
| Dimensions | 50*27*50.5cm | |
| Weight | 19Kg | |
Installation Attentions
- Input voltage: AC180-420V 50/60Hz
- Input cable: ≥4mm², length ≤3m
- Power switch: 63A
- Output cable: ≥25mm², length ≤20m
- Ambient temperature: -10℃~+40℃
- Usage condition: No blocked on air inlet & outlet, no sunlight exposure, pay attention to dust prevention.
- Gas tank installation: Fix firmly to avoid collision and place in a cool place.
Standard Accessories
1x Electrode Holder
1x Ground Clamp
1x Welding Mask
1x Brush/Hammer
Optional Accessories
Welding Helmet
Welding Gloves
Electrodes E6013
Lift TIG Torch
Frequently Asked Questions
The welder should be installed in a firm, dry area (humidity ≤ 90%) with an ambient temperature between -10°C and +40°C. Avoid locations with water splashes, dust, corrosive gases, or tabletop inclinations greater than 15°.
Although the welder features an automatic voltage compensation circuit to keep the welding current within the allowable range, supply voltage that exceeds the allowable limit will damage the machine.
Do not pull out the power plug. Leave the machine turned on so the cooling fan can run. Once the temperature drops to the standard range and the yellow indicator light turns off, you can resume welding operations.
The installation requires an input voltage of AC180-420V 50/60Hz, an input cable of ≥4mm² (length ≤3m), a 63A power switch, and an output cable of ≥25mm² (length ≤20m).
The standard accessories package includes 1x Electrode Holder, 1x Ground Clamp, 1x Welding Mask, and 1x Brush/Hammer.
Yes, a Lift TIG Torch is available as an optional accessory to extend the versatility of the welding machine.